Skip to main content

Garburator Won't Reset After a Jam: 4 Steps to Fix It

If your garburator won't reset after a jam, pressing the reset button harder is not the answer. The button won't stay in until two conditions are met: the unit has cooled down, and the jam is fully cleared. Press reset while the flywheel is still blocked and the button pops straight back out. That's not a broken garburator, that's a working safety system doing its job.

Most garburator "failures" we get called for in Coquitlam and the Lower Mainland come down to this exact situation. The unit trips its thermal overload, someone tries to reset it immediately, it doesn't work, and suddenly a $0 fix looks like a service call. The four steps below clear the jam, cool the motor, and get the unit running again, usually in under 30 minutes.

Key Takeaways
  • The reset button won't hold if the flywheel is still blocked or the motor is still hot
  • Let the unit cool for 15 to 20 minutes before attempting a reset
  • Use a 1/4-inch hex key in the port on the underside to manually free the flywheel
  • Check the circuit breaker if the unit is completely silent, no hum, no response at all
  • If the button won't stay in after clearing the jam and cooling, the thermal overload fuse may be blown
  • Garburators jam far more often than they actually break. Try these steps first
Stainless steel kitchen sink with chrome faucet — garburator reset troubleshooting

1. Why Your Garburator Won't Reset

Most garburators have a thermal overload protector, a small red or black button on the underside of the unit. When the motor overheats from a jam, the protector trips and cuts power. The button pops out about 5 mm to signal it has tripped.

Here's where people get stuck (the garburator pun writes itself): the overload protector will not reset while the motor is still hot, and it will not reset while the flywheel is still physically blocked. You need both conditions cleared before the reset has any chance of holding.

Three things cause the reset button to refuse to stay in:

  • The motor is still overheated from the jam event
  • The flywheel is still blocked by whatever caused the jam
  • The thermal overload fuse is blown entirely, which requires a technician

The good news: the first two are fixable in your kitchen in about 20 minutes. The third is uncommon, but it happens when a unit has been repeatedly forced against a jam without clearing it first.

If you want a full overview of common garburator problems beyond reset issues, our garburator repair guide covers the most frequent causes we see in the Lower Mainland.

2. Step 1: Let It Cool Down (15 to 20 Minutes)

Turn the garburator off at the wall switch. Do not try to run it. Do not press reset yet. Let the unit sit for at least 15 minutes, 20 if the motor was running hard before it tripped.

The thermal overload protector monitors motor temperature. Push reset before the motor cools and the protector senses the motor is still at risk, so the button pops out immediately. This is the step most homeowners skip, which is why garburator reset attempts fail on the first three tries.

While you're waiting: turn off the cold water, take a torch (the phone kind, not the house-fire kind) and look down into the drain opening. You may be able to see what caused the jam.

If the unit is completely silent, no hum, no buzz, nothing at all, skip ahead to Step 4 and check the circuit breaker first. A completely dead unit may have tripped the breaker rather than the thermal overload.

3. Step 2: Free the Flywheel with a Hex Key

This is the most important step. The reset button will not hold if the flywheel is still blocked, no matter how long you wait for it to cool.

What you need: a 1/4-inch (6 mm) hex key (Allen wrench). Most garburators come with one stored in a clip on the unit itself. If yours is gone, a standard hex key set has one.

How to do it:

  1. Turn the wall switch off and unplug the unit from under the sink.
  2. Find the hex socket on the centre underside of the garburator.
  3. Insert the 1/4-inch hex key and work it back and forth in both directions.
  4. You will feel resistance where the obstruction is. Keep working until the flywheel spins freely through a full rotation in both directions.
  5. Once it moves freely, use tongs or long-nose pliers to remove the obstruction from the drain opening. Do not use your fingers.

The two items we pull out most often: a small bone or hard pit, and the bottle cap someone "thought would be fine." (It was not fine. It is never fine. And yet, here we are.)

Once the flywheel spins freely, proceed to Step 3.

4. Step 3: Press the Reset Button Correctly

Find the reset button on the underside of the garburator unit. It's typically a small red or black button in the centre, and it should be protruding about 5 mm if the thermal overload has tripped.

How to reset correctly:

  1. Confirm the unit is still unplugged.
  2. Press the reset button firmly until you feel it click and seat flush with the unit housing.
  3. If it clicks and holds, plug the unit back in.
  4. Turn on cold water at the tap.
  5. Flip the wall switch.

The unit should start immediately. Run cold water for 30 seconds and listen for normal operation.

If the button clicks and holds but the unit still doesn't respond when you flip the switch, check the circuit breaker in Step 4 before assuming the motor has failed.

If the button pops back out when you press it, the motor may still be warm or there's still an obstruction. Wait another 10 minutes, recheck the hex port, and try again.

5. Step 4: Check the Circuit Breaker

If the garburator shows no signs of life, no hum, no buzz, nothing, before you assume the motor is gone, check the circuit breaker.

Garburators run on a dedicated circuit or a shared circuit with the dishwasher. A heavy jam can trip the breaker. This is a 20-second check that gets skipped on a surprising number of service calls.

Head to your electrical panel. Find the breaker labelled "disposal," "garburator," or "kitchen" (many residential panels in the Lower Mainland are a mystery, honestly). Look for a breaker that sits in the middle position rather than fully on or fully off. Flip it fully off, then back to on.

Return to the garburator, confirm the unit is plugged in and the reset button is seated, then try the switch.

For guidance on identifying a tripped breaker safely, Technical Safety BC's electrical safety resources are a useful reference for BC homeowners who want to understand their panel before touching it.

Still nothing after the breaker check? Now it's worth calling a technician.

6. When the Reset Still Won't Hold

You've cooled the motor, freed the flywheel, seated the reset button, and checked the breaker. The reset button still won't stay in, or the unit hums but doesn't spin, or the button holds but the unit trips again within seconds of starting.

At this point, one of three things is happening:

The thermal overload fuse is blown. This is a consumable component inside the unit. It blows when a motor has been forced against a jam repeatedly, doing its job and then it's done. Replacement is possible on most units but requires disassembly and a confirmed diagnosis first.

The motor has failed. On a garburator under 8 years old, motor failure outside of a jam is uncommon. On a unit 10 years or older, the motor may have simply reached the end of its service life. Age matters here as much as the symptoms.

Something is physically damaged inside. Impellers and shredder rings can crack or deform under extreme load. The unit may run but grind poorly, or trip repeatedly on normal food waste. This is a hands-on diagnosis, not something you can determine from the outside.

All three need a technician. If you're in Port Coquitlam or anywhere across the Lower Mainland, give us a call at (778) 941-7758. We can usually tell you in five minutes on the phone whether a visit is going to be worth it or whether you're better off replacing the unit.

7. Repair vs. Replace: When to Stop Resetting

Here's a position we hold based on years of service calls: garburators jam, they almost never break. The reset button and a hex key clear the majority of garburator "failures" we get called for. We have never once been annoyed that a homeowner tried these steps first before calling us. That's a $0 fix on most jobs.

But there is a point where replacing is the smarter call.

Replace the garburator if:

  • The unit is 10 years or older and the motor has failed
  • The repair cost exceeds 50% of what a comparable new unit costs installed
  • The unit has jammed and been reset more than twice in the same month, because at that point the problem is the unit, not the food going into it
  • There are signs of internal water damage or a cracked housing

Repair makes sense if:

  • The unit is under 10 years old and the issue is a blown thermal fuse, an inexpensive consumable
  • The jam caused physical damage to the impellers but the motor and housing are sound
  • The unit is a higher-end model where the replacement cost is significant

A basic garburator replacement runs $300 to $600 installed for a mid-range unit in the Lower Mainland. A thermal fuse replacement is considerably less. We quote both clearly before starting any work, so you can make an informed decision rather than finding out what "a bit more" means at invoice time.

8. How to Prevent Future Garburator Jams

The best garburator reset is the one you never have to do.

What the garburator handles well:

  • Soft food scraps: cooked vegetables, fruit flesh, small amounts of leftover food
  • Citrus rinds in small pieces
  • Ice cubes occasionally, to clean the grinding chamber

What causes most jams:

  • Fruit pits, avocado pits, peach pits, cherry pits
  • Bones, even small ones from chicken or fish
  • Fibrous vegetables: celery, artichoke leaves, corn husks
  • Grease and fat poured while hot, it coats the chamber and slows the grinding plate over time
  • Bottle caps and small utensils (the classics, and yet)

One rule covers most situations: if you wouldn't compost it, don't put it in the garburator. Metro Vancouver's food scraps composting programme is a practical alternative for the items your garburator can't safely handle, including bones, pits, and fibrous waste.

Also: always run cold water before turning the unit on, keep it running throughout, and let it run for 15 seconds after you turn the unit off. Cold water solidifies any fat so it gets ground and flushed rather than building up on the chamber walls.

About the author

Max is a certified appliance repair technician serving Port Coquitlam and the Lower Mainland. He is the lead technician at ElectraFix Appliance Repair Ltd. and has been diagnosing garburator and kitchen appliance problems in BC homes since [VERIFY — year].

Frequently Asked Questions

Why won't my garburator reset button stay in?

The reset button pops back out when the flywheel is still physically blocked or the motor is still overheated from the jam. Both conditions need to be cleared before the reset will hold. Free the flywheel with a 1/4-inch hex key, let the motor cool for 15 to 20 minutes, and then try the reset again. If it still won't hold after that, the thermal overload fuse may be blown and the unit needs a technician.

How do I use a hex key to unjam a garburator?

Turn off the wall switch and unplug the unit. Insert a 1/4-inch (6 mm) hex key into the socket on the centre underside of the garburator. Work it back and forth in both directions until the flywheel rotates freely through a full turn. Remove the obstruction with tongs, never your fingers, then press the reset button and restore power.

Where is the reset button on a garburator?

The reset button sits on the underside of the garburator unit, typically in the centre. It is usually red or black and protrudes about 5 mm when the thermal overload has tripped. You'll need to crouch under the sink to reach it. Press it firmly until it clicks flush with the housing.

What does it mean when my garburator hums but won't spin?

A humming garburator that won't spin means the motor has power but the flywheel is physically blocked. The motor is running but cannot rotate against the obstruction. Turn the unit off immediately to prevent motor burnout, unplug it, and use a 1/4-inch hex key to free the flywheel before attempting a reset. Running a jammed motor continuously is how a $0 fix turns into a motor replacement.

How long should a garburator last?

Most garburators last 8 to 12 years with normal use. Units that handle hard items like bones, pits, and bottle caps regularly tend to wear faster. If your unit is approaching 10 years old and the motor has failed, replacement usually makes more financial sense than repair. A mid-range unit installed in the Lower Mainland runs $300 to $600.

When should I replace my garburator rather than trying to fix it?

Replace if the unit is 10 or more years old and the motor has failed, if the repair cost exceeds 50% of a comparable new unit installed, or if the unit has jammed and been reset more than twice in the same month. A basic garburator replacement runs $300 to $600 installed for a mid-range unit in the Lower Mainland. Call us to get a quote on both repair and replacement before committing to either.

Is it safe to put my hand into a garburator?

No. Always unplug the unit before reaching anywhere near the drain opening. Even with the wall switch off, the unit can still have power if it remains plugged in. Use tongs or long-nose pliers to remove obstructions. The impellers are not sharp but can cause serious injury if the unit starts unexpectedly. Unplug first, every time.

Back to top

If the reset button still won't hold, we'll take it from here.

We can usually tell you on the phone whether it's worth a service visit or whether you're better off with a new unit. We will also not judge what we find in the hex port. (We have seen things. Many, many things.)

(778) 941-7758

ElectraFix Appliance Repair Ltd.

Need a technician? See our Garburator Repair service page for same-day bookings across the Lower Mainland, or call (778) 941-7758.