Dishwasher Repair Services

24 -Hours Emergency Services

Satisfaction
Guaranteed

Same day service

Fast and reliable
Trusted Appliance Repair Across the Lower Mainland
See why local homeowners choose ElectraFix for fast, reliable appliance repairs.
Dishwasher Repair Services

ElectraFix repairs dishwashers across the Lower Mainland, covering all major makes and models from standard freestanding units to fully integrated Bosch and Miele configurations. The most common dishwasher calls we receive are drainage failures, door leaks, dishes not cleaning, and units that will not start. Before you book a technician, there are two checks worth completing first, either one resolves the majority of calls without a visit. If those steps do not fix the problem, we carry parts for all major brands on the service vehicle and complete most Lower Mainland dishwasher repairs on the first visit. Call (778) 941-7758 for same-day or next-day availability.
Before You Call
Approximately 60 to 70 percent of dishwasher drainage calls are caused by a clogged filter. The filter basket sits at the base of the dishwasher tub. Pull it out, rinse it under running water, clear any debris from the mesh screen, and reinstall it. This takes two minutes and costs nothing. If the dishwasher drains normally after that, the job is done.
If your dishwasher or washing machine stopped filling with water, check that the water inlet valve behind the appliance has not been bumped closed. It can shift position when the appliance is moved or pushed back against the wall. It is the first thing we check when we arrive on a no-fill call.
Neither step requires tools. If you have tried both and the problem continues, call us, and let us know what you found when you checked, to help narrow down the diagnosis before the technician arrives.
Common Dishwasher Problems We Fix
Dishwasher Not Draining
If the filter is clean and the dishwasher still will not drain, the fault is most likely in the drain pump, the drain hose, or the drain solenoid. The drain pump pushes water through the drain hose at the end of each cycle. If the pump motor has failed, there will be standing water in the bottom of the tub after the cycle ends. We test the drain pump with a multimeter, if there is no continuity, the pump needs replacing. Blockages in the drain hose and a stuck drain valve produce the same symptom and are typically less expensive to resolve than a pump replacement. The drain impeller, which sits inside the drain pump assembly and moves water into the hose, can also break a blade and stop water movement without the motor itself failing.
Dishwasher Leaking
Leaks come from several sources and the repair cost varies significantly depending on which one is responsible. The door gasket is the most common cause, it cracks or deforms with age, and water escapes around the door seal during the wash cycle. Gasket replacement is a straightforward repair. If the leak is from underneath the appliance rather than around the door, the water inlet valve or wash arm assemblies are more likely causes. The water inlet valve controls water entry to the tub and can stick open, allowing water to overflow. Wash arm assemblies that have cracked direct water against the door frame rather than inward, which produces a leak that looks like a door seal problem but is not.
Dishes Not Coming Out Clean
Dishes that come out dirty, cloudy, or with food residue are most often caused by blocked spray arms, a clogged filter, or insufficient water entering the machine. The spray arms have small holes that distribute water across the dish rack during the wash cycle. These holes accumulate mineral deposits and food particles over time. Removing the spray arms and clearing the holes manually resolves poor cleaning in many cases. If the spray arms are clean and the cleaning result is still poor, the water inlet valve may not be delivering sufficient water volume, or the circulation pump motor may be running below its designed flow rate.
Dishwasher Not Starting
A dishwasher that will not start at all typically has one of three faults: a failed door latch, a blown thermal fuse, or a faulty door switch. The door switch signals the control board that the door is closed and the cycle can begin. If any of the two or three door switches fail, the dishwasher reads the door as open and refuses to run, this is a safety design, not a random fault. The thermal fuse blows if the dishwasher overheats and prevents it from restarting until the fuse is replaced. Control board failures are less common and are frequently misdiagnosed, we work through the door latch, switches, and fuse before concluding the control board is at fault.
Dishwasher Making Noise
Grinding or rattling during a cycle usually indicates debris in the drain pump or a worn bearing in the circulation pump. A piece of broken glass or a small utensil caught in the pump impeller produces a grinding noise that sounds serious but is often a straightforward clearance. If the pump is clean and the noise continues, the circulation pump bearings are likely worn, this produces a lower groaning sound as the motor strains rather than a sharp grinding. A wash impeller with a broken blade makes a rhythmic clicking sound as it rotates.
Dishwasher Not Drying
If dishes come out wet regardless of drying settings, the heating element or the vent fan motor is the most common cause depending on the model. Dishwashers that use a heating element to dry dishes can be tested with a multimeter for continuity. Models that use condensation drying, most Bosch dishwashers, for example, do not have a traditional heating element and rely on the temperature differential between the wash cycle and the internal walls. Poor drying on condensation-drying models is often a water temperature issue rather than a component failure. If the dishwasher has a vent that opens at the end of the drying cycle, a stuck or broken vent prevents steam from escaping and leaves dishes wet.
Soap Dispenser Not Releasing Detergent
The soap dispenser is a spring-loaded compartment with a bi-metal actuator that opens the door at a set point in the wash cycle. If the actuator has burned out, the dispenser door does not open and detergent stays in the compartment through the entire cycle. Detergent left in the dispenser after a completed cycle, with the door still closed, confirms this fault. A dispenser door that opens but does not fully release the tablet or pod is more likely a spring or latch issue than an actuator failure.
Control Panel or Buttons Not Responding
Buttons that do not register inputs, or a display that has gone blank, are most commonly caused by a failed membrane keypad or a control board fault. On many dishwasher models, the touchpad and control board are sold as a single assembly. Before replacing either component, we verify that the issue is not a locked or child-proofed control panel, most dishwasher brands use a button-hold combination to lock and unlock the controls, and a locked panel displays the same symptom as a failed touchpad.
Flashing Lights or Error Codes
Flashing indicator lights combined with an error code on the display point to a specific fault logged by the control board. The diagnostic code identifies the fault, drain failure, water supply failure, temperature fault, or door fault, and allows us to target the repair without testing every component. We carry the technical documentation for all major brands on the service vehicle. If your dishwasher is flashing lights without a clear error code, note how many times the light flashes before it pauses, most brands use flash sequences to communicate specific faults.
Dishwasher Types We Service
Freestanding Dishwashers
Standard freestanding dishwashers are the most straightforward configuration to service. The appliance slides out from under the counter without dismantling surrounding cabinetry, and all major components are accessible within 15 minutes of arrival. Labour time is lower than for built-in and integrated configurations.
Built-In and Integrated Dishwashers
Built-in dishwashers with a decorative panel attached to the door, common in kitchen renovations using Bosch, Miele, AEG, and Fisher and Paykel units, require removing the panel before the door can be serviced and removing the mounting screws from the underside of the counter before the unit can be slid out. This adds access time that is included in the quoted labour. Fully integrated models where the front of the door is flush with the surrounding cabinet face have the longest access time of any dishwasher configuration. At the purchase price of integrated dishwashers, typically $1,200 to $3,000, repair is almost always the right financial call, and we account for the additional access time transparently in every estimate.
Compact and Drawer Dishwashers
Compact countertop dishwashers and drawer dishwashers, Fisher and Paykel DishDrawer models in particular, have a different internal layout than standard under-counter units. Drawer dishwashers are particularly common in New Westminster, North Vancouver, and West Vancouver kitchens where counter space is limited or two-drawer configurations allow partial loads to run independently. We service both single and double DishDrawer configurations. Parts availability for compact models is occasionally the limiting factor; we confirm sourcing before scheduling the repair.
Dishwasher Repair Frequently Asked Questions
DISHWASHER IS NOT DRAINING
In many cases, the dishwasher will stop draining or draining fully due to clogged drainage hoses or due to an object caught in the draining pump. There are some cases when the draining pump is faulty and needs to be replaced. We have assembled the top issues to check for a dishwasher that does not drain.
- Drain Pump: The drain pump in your dishwasher pushes water through the drain hose. If the drain pump motor is malfunctioning the dishwasher will not drain. Drain pumps can be checked with a multimeter. If there is no continuity then it must be replaced with a new part.
- Drain / Wash Impeller: The dishwasher drain impeller or wash impeller is connected to the drain pump. It allows water to flow through to the garbage disposal or drain line. If it is broken it needs to be replaced with a new part.
- Drain Solenoid Kit: The drain solenoid electronically opens the drain valve to allow water to exit the dishwasher. This solenoid can be tested with a multimeter and replaced or repair as required.
- Drain Valve: It is possible that the drain valve of the dishwasher has a blockage. It needs to be removed and inspected. If it is broken it needs to be replaced with a new part.
DISHWASHER IS LEAKING
A leaking dishwasher is a common repair problem. Dishwashers will leak due to a problem with the water inlet valve that isn’t connected properly or just faulty, unfortunately, these cannot be repaired by a professional and need to be replaced. There are times when the door seal is ripped or cracked and that would be the reason for the leaking dishwasher.
- Water Inlet Valve: The dishwasher water inlet valve allows water to flow into the dishwasher. It can become stuck in the open position letting water continue to flow.
- Wash Arm Assemblies: There is a lower wash arm, center wash arm, and upper wash arm assembly. These parts are where the water sprays out to clean your dishes. If there are any cracks in these arm assemblies then water may be sprayed directly against the dishwasher door causing a leak. A quick repair can be done by making sure the wash arm assemblies are not loose by making sure all the screws are tight.
- Door Seal: Inspect the dishwasher’s main door seal for any evidence of cracks or wear. Watch the door seal closely while the dishwasher runs to inspect it for leaks.
DISHWASHER IS NOT CLEANING
When the dishwasher stops cleaning, it really becomes useless. A faulty water inlet valve might be the reason for that, if not enough water is coming into the unit it would have a hard time cleaning the dishes. Also if the lower or upper arms are clogged they would not distribute water to the dishes in the necessary amount, most of the time just taking them out and cleaning them would solve the problem.
- Water Pump Belt: First determine if your appliance model has a water pump belt. The dishwasher water pump belt is located behind the lower access panel. Use a multimeter to test for continuity and replace accordingly.
- Water Inlet Valve If the dishwasher water inlet valve is clogged or broken then water can’t enter the machine properly.
- Wash Arm Assemblies: In the dishwasher, the wash arms distribute the water to wash your dishes. They can become clogged and cracked over time. Inspect them carefully and clean or replace them as needed.
- Circulation Pump: The dishwasher circulation pump uses a motor to force water through the control arms. If the motor is not making any noise it may be burned out. Ensure power is getting to the motor. make sure the impeller can turn (it may have a blockage). This can be a difficult repair and one of the most expensive parts of a dishwasher.
DISHWASHER IS NOT STARTING
If you can’t get your dishwasher to start the cycle it might be due to something simple like a burned fuse. There are times when there is a problem with the door switch that prevents the appliance from starting the cycle. Also, a broken door latch would cause the same thing to happen.
- Thermal Fuse: The thermal fuse is designed to shut off power if the dishwasher overheats. If this fuse blows the dishwasher will not start. You can test the thermal fuse with a multimeter and replace it as required.
- Door Switch: If the door switch does not engage the dishwasher will not run. The dishwasher will think the door is still open. Test the door switch with a multimeter for continuity.
- Control Panels and Touchpads: Your dishwasher control panels and touchpads have lots of electronics in them that can malfunction. They are however rarely the culprit and are often misdiagnosed. These panels must often be replaced as the individual components are sometimes not available.
DISHWASHER IS NOISY
When the dishwasher starts to make funny noises or work loud it is usually because there is debris caught in the draining pump, although a problem with the motor is not an exception.
- Drain Pump: The dishwasher drain pump needs to be checked for debris. If it’s clean and noisy it needs to be replaced.
- Circulation Pump: Bearings inside the circulation pump will wear out over time and can cause a load “groan” while the dishwasher operates.
- Wash Impeller: The wash impeller has small plastic blades that help with water flow to the control arms. If one of the blades breaks, there could be noise. It may also be improperly aligned. Inspect for any signs of damage.
DISHWASHER BUTTONS NOT WORKING
If the dishwasher is working but you get no response when you press the control buttons the reason for that is probably either a faulty touchpad, faulty control panel, or the main control board.
- Touchpad and Control Panel: If some buttons work and others don’t it is likely that the entire piece needs to be replaced. It depends on your dishwasher’s maker and model if the touchpad and control panel are sold as one unit or separately.
- Main Control Board: The main control board regulates all the functions of your dishwasher. This is a highly misdiagnosed problem so make sure everything else is tested first. Our repair technicians can use a multimeter and electric schematics to determine if the control board is at fault.
DISHWASHER IS NOT DRYING
When it comes to drying our dishes we are talking about the heating elements and vents. Sometimes all it takes is to set your dishwasher’s drying setting to a longer time frame.
- Vent: If the dishwasher vent is not functioning properly then the steam can’t escape and your dishes won’t dry. Check to make sure the vent can open.
- Vent Fan Motor:Some dishwasher models have a vent fan motor that helps to dry the dishes and remove moisture from inside the machine. Use a multimeter to test for continuity. Also, try hand-turning the blade. It should spin freely.
- Heating Element:Some dishwashers use a heating element to dry the dishes. It needs to be checked with a multimeter to determine if it is working or needs repair.
DISHWASHER NOT DISPENSING SOAP
There are many different components depending on your brand and model of the dishwasher that could be preventing the soap from dispensing properly. The detergent container has springs, lids, latches, and doors that must all be examined to ensure they are functioning properly or are in need of repair.
- Bi-Metal Actuator: Some dishwashers have an electronically operated bi-metal actuator that could be burned out. It needs to be checked with a multimeter. Another issue that can affect the bi-metal is if your dishwashing machine is not getting enough water.
DISHWASHER LIGHTS FLASHING
If the dishwasher lights are flashing or blinking, and there is an error code in the display window, consult the wiring diagram, tech sheet, and dishwasher manual to find out more information about the error.
Dishwasher Brands We Service
We repair all major dishwasher brands across the Lower Mainland including Bosch, Miele, LG, Samsung, Whirlpool, KitchenAid, Maytag, Frigidaire, GE, Electrolux, Kenmore, Jenn-Air, Fisher and Paykel, AEG, Blomberg, and more. Bosch and Miele are the most frequently requested premium brands in our service area. Bosch parts are well-stocked across our service vehicle inventory. Miele parts occasionally require 2 to 4 weeks to source through Canadian distributors, if you have a Miele dishwasher fault, call early so the parts timeline does not extend your wait.
Articles you may find interesting:
ElectraFix Appliance Repair
Book your dishwasher repair - call (778) 941-7758
- ✓ Same-day service availability
- ✓ Written quote before any work starts
- ✓ Diagnostic fee credited against the repair if you proceed

