Samsung Washing Machine Error Codes: What They Mean and What to Do About Them
A Samsung washing machine error code is the appliance's way of telling you something specific has gone wrong, not a random insult, even when it feels like one at 11pm with a drum full of wet laundry. Each code points to a specific system: water supply, drain, door, motor, heating element, balance detection. Most codes have a straightforward check you can do yourself. Some require a technician. And a few are Samsung's politely worded way of informing you that a component has failed and the display code is the least of your problems.
This guide covers every common code, what each one actually means, what to try first, and when to put down the manual and call someone who has the diagnostic tools to read what the display is not telling you.
- Samsung uses alphanumeric codes, and the same fault often displays differently by model — 4E on one machine is E1 on another. The surface code is not the full picture.
- Start every code with the 30-second reset: Power off, wait 30 seconds, Power on. Clears transient faults. If it comes back, something has actually failed.
- Water supply (4E), drain (5E), and unbalanced load (UE) account for the majority of Samsung washer service calls — and most resolve without a technician.
- The SUd code is almost always the wrong detergent or too much of it. Not a mechanical fault.
- 3E and AE codes have sub-codes that look identical on the display but indicate completely different faults — some minor, some requiring control board replacement.
- Samsung's diagnostic mode runs each component independently and surfaces fault data the panel code does not show. Most owners have never used it.
- If the same code returns after two resets, stop troubleshooting and call a technician. You are not fixing anything by clearing a code that keeps coming back.
1. How Samsung Error Codes Work (and Why They Are Confusing)
Before the code list, a thing worth knowing: Samsung's error code system has a design quirk nobody puts on the box. The same fault often displays as a different code depending on the model and year. What shows as 4E on a 2019 front-loader might display as E1 on a 2015 top-loader, as 1 4C on a 2022 unit, or occasionally as a blinking light sequence with no alphanumeric code at all.
This is not a documentation accident. Samsung — like LG — uses a proprietary diagnostic architecture. The codes on the panel are surface-level indicators. The full diagnostic data lives in a service mode that requires Samsung's service software or a technician who knows the model-specific fault tree. A general handyman looking up your code online is reading the same surface display you can see yourself. An experienced Samsung tech with the right tools is reading a different data set entirely. This distinction matters most when the code involves the motor or control board — two repairs where the sub-code determines whether you are looking at a $120 sensor or a $500 board replacement.
The reset that works on many temporary faults: press Power to turn the machine fully off, wait 30 seconds, press Power to restart. If the code clears and does not return within two cycles, it was a transient fault — power fluctuation, momentary sensor reading, brief water pressure drop. If it comes back, read the relevant section below and stop resetting.
One more thing before the codes: unplug the machine before opening any access panel or touching any component. Wait five minutes after unplugging — Samsung's capacitors hold a charge after the machine is switched off. Technical Safety BC recommends treating any large appliance as live until you have confirmed the capacitors have discharged. (They do not announce this. The charge announces itself. This is the less fun version of a surprise.)
2. Water Supply Errors: 4E, 4C, nF, CE, 4C2
What it means: The machine started a fill cycle and could not get enough water within the expected time. This is among the most common Samsung washer codes, and the majority of cases resolve without a technician.
What to check, in order:
- Water tap fully open? The supply tap behind the machine gets bumped when the machine is moved or when other work is done nearby. It is the first thing checked on every service call. Takes five seconds. Do it before calling anyone.
- Inlet hose kinked or crushed? If the machine was pushed back against the wall after installation, the hose can kink completely. Pull the machine forward and confirm the hose has a clear, unobstructed run from the tap to the back of the machine.
- Inlet filter blocked? The small mesh filter inside the inlet valve connection at the back of the machine collects sediment over time. Unscrew the inlet hose, pull the filter out with needle-nose pliers, and rinse it under the tap. If you are in the Abbotsford, Chilliwack, or Langley areas, note that Fraser Valley water hardness is above the provincial average. That accelerates limescale buildup in inlet filters significantly faster than the Lower Mainland average. Clean this filter every 6 months if you are in a hard-water zone.
- Water pressure too low? Samsung front-loaders require a minimum of 0.5 bar of inlet pressure. In older buildings where supply pressure is generally low, the machine will time out and throw a 4E before the drum is adequately filled. If pressure is low house-wide, the solution is upstream of the machine.
- 4C2 specifically? This variant means the hot and cold inlet hoses are reversed, cold water is going to the hot inlet and vice versa. If the hose connections were disturbed during a recent move or plumbing visit, confirm that cold goes to cold and hot goes to hot. Marked on the machine and on the hoses. It happens more often than the frequency of the call suggests.
When to call a technician: Tap open, filter clean, hose unkinked, house pressure normal — code still returns. The inlet solenoid valve has likely failed. This is a parts-and-labour repair, completed in a single visit on most Samsung models.
3. Drain Errors: 5E, 5C, nd, SE
What it means: The machine washed the clothes successfully and is now declining to drain the water out. This code appears most often at the transition from wash to spin, when the drain pump activates.
What to check:
- Drain pump filter. This is the fix for roughly 60 to 70% of drain error calls, and it is the thing most guides underemphasise. On Samsung front-loaders, the drain pump filter sits behind a small access panel at the bottom front of the machine. Put towels down. Put a shallow tray under the access cap before opening it, the water coming out is warm, grey, and contains everything that fell out of pockets over the last year. Coins, hairpins, children's small toys, the mystery object responsible for that noise three months ago. Clean the filter under the tap, check the pump cavity for debris, reinstall, and run a drain cycle. If the 5E clears, you found it.
- Drain hose positioning. The drain hose should enter a standpipe at between 15 cm and 100 cm above floor level. Too low and water siphons back continuously. Too far into the standpipe, beyond 15 cm depth, and an air lock prevents drainage. Neither position is obvious without pulling the machine forward to check.
- Drain hose blockage. Disconnect the hose from the standpipe and check for obstruction. On longer hose runs or where the hose bends sharply, lint accumulation can create a partial or full blockage over time.
- Machine level? A machine tilted significantly toward the rear can prevent the drain pump from clearing the sump effectively. Check with a spirit level across the top of the machine in both directions.
When to call a technician: Filter clean, hose correctly positioned, machine level, 5E still returns. The drain pump motor has failed. This is a one-visit repair on most Samsung front-loaders. Get the diagnostic confirmed before authorising a pump replacement; on some models, a blocked pump housing rather than a failed motor produces the same code and costs considerably less to fix.
Still seeing the 5E after cleaning the filter?
The drain pump motor has likely failed. Our technicians serve Port Coquitlam, Vancouver, Burnaby, Surrey, and the Lower Mainland — rated 4.6 stars across 934 Google reviews. We diagnose before we quote, and the diagnostic fee comes off the repair if you proceed.
(778) 941-77584. Door and Lock Errors: dE, dC, FL, dL, dC1, dC4
What it means: The machine will not start, or it stopped mid-cycle, because the door lock interlock is not satisfied. The machine genuinely believes the door is not closed and locked, and it will not spin with an open door, for reasons that should be obvious to anyone who has seen what happens when it tries.
What to check:
- Is laundry caught in the door seal? A single sock wedged in the rubber gasket is enough to prevent the latch from fully engaging. Open the door and check the seal all the way around the circumference. Remove anything caught in it.
- Is the door fully closed? Push it firmly until you hear the latch click. On some Samsung models, the click is quiet enough that it is easy to assume the door is latched when it is not quite there.
- Is the door latch visibly damaged? Inspect the plastic hook on the door and the receiver on the body. Cracked, worn, or bent components will not engage the interlock reliably. The latch assembly is a straightforward parts replacement on most Samsung models.
- dC1 and dC4 sub-codes: These indicate the door lock motor or microswitch has failed rather than the latch alignment. If you see a numbered suffix on the dC code, the lock mechanism needs replacing rather than adjusting.
When to call a technician: Do not attempt to override or bypass the door interlock to run the machine. It is also the flood prevention system. A machine that runs with a failed interlock can open under spin pressure. The interlock is a $40 to $90 part on most Samsung models, not a reason to improvise.
5. Unbalanced Load Errors: UE, UB, Ur, U6
What it means: The machine has detected that the laundry is unevenly distributed in the drum and has declined to proceed with the spin cycle on those terms. Your washing machine, it turns out, has opinions about how you loaded it. Unlike most entities with strong opinions, it will act on them.
What to check:
- Redistribute the load. Open the door, separate items that have bundled together, and spread them evenly around the drum. Heavy items, duvet inserts, bath towels, jeans, clump during the wash cycle and create asymmetric weight the machine cannot spin out safely.
- Check load size. Too small a load creates the same problem as a misbalanced one. A single heavy item will never achieve balance in a partially-filled drum. Add a few towels to bring the weight to a more even distribution.
- Check the machine is level. A machine not sitting flat on all four levelling feet reads a balanced load as unbalanced. Adjust the feet until a spirit level reads true across the top in both directions.
- Ur specifically means the drum cannot rotate at all during the balance attempt, the asymmetry is severe enough that the machine will not move. Redistribute the load completely and restart from a drain cycle rather than a full cycle.
When to call a technician: A UE code that returns on every cycle with a properly balanced load on a level machine indicates worn suspension rods or shock absorbers. The machine is reading normal drum movement as imbalance because the damping components are no longer doing their job.
6. Excess Suds: SUd, Sd
What it means: The machine has paused to deal with a foam situation. It will wait for the suds to dissipate before attempting to drain or spin. This code is almost entirely caused by one of two things: too much detergent, or the wrong type.
Samsung front-loaders require HE (High Efficiency) detergent only. Standard detergent, designed for older top-loaders with full water agitation, produces several times more foam than an HE machine can handle. If you want to understand exactly how HE washers differ from traditional models and why detergent type matters so much, that post covers it in detail. The short version: if you have been using non-HE detergent in a Samsung front-loader, the SUd code is not a malfunction. It is the machine correctly identifying a problem you created.
A secondary cause: detergent dosing. Detergent manufacturers have a financial interest in customers using more product than necessary. The dosing instructions on most containers exceed what a modern HE machine requires for a standard load. The SUd code is the machine's independent counter-argument to the packaging.
What to do when you see SUd:
- Do not open the door mid-cycle.
- Let the machine run automatically, it will attempt a rinse and drain cycle to clear the foam. In severe cases this pause lasts up to 30 minutes. That is normal.
- After the cycle completes, run a hot empty cycle with no detergent to clear residual soap from the drum and pump.
Going forward: HE detergent only, dosed at roughly half the packaging recommendation for a normal load.
When to call a technician: Almost never for a SUd code. The one exception is a SUd code that appears consistently even with correctly-dosed HE detergent, in that case, the foam level sensor has likely failed and is reporting suds that are not there.
7. Temperature and Heating Errors: tE, HE, HE1, HE2
What it means: Something in the temperature measurement or heating system has failed. These codes split into two groups — problems with measuring temperature (tE) and problems with generating heat (HE).
tE codes (temperature sensor fault):
The NTC thermistor measures water temperature and sends readings to the control board. When it fails or reads outside expected parameters, the board throws a tE code. A failed thermistor does not stop the wash from running, it stops heated washes from running at the correct temperature. The machine defaults to cold and flags the fault.
- tE1 — main wash temperature sensor
- tE2 — rinse temperature sensor (on models with heated rinse)
- tE3 — condenser temperature sensor on heat-pump washer-dryer models
HE codes (heating element fault):
The heating element itself has failed or is not drawing current correctly through the control circuit.
- HE1 — heating element fault during the wash cycle
- HE2 — heating element fault during the drying phase on combo washer-dryer units
What to try first: Full power cycle, unplug from the wall for 5 minutes, not just pressing pause. Temperature sensor faults are occasionally triggered by a transient resistance reading rather than a dead component. If the code does not return after the reset and a full cycle, monitor for recurrence over the following week.
When to call a technician: tE and HE codes that return after a full reset indicate component failure. The heating circuit carries line voltage. This is not a safe amateur repair regardless of what the tutorial video suggests.
8. Motor Errors: 3E, 3E1–3E4, Lr
What it means: This is the section where Samsung's error code system gets genuinely opaque, and where the gap between the surface code and the actual fault matters most.
The base code 3E tells you the motor system has an issue. The sub-codes tell you which specific issue, and they are very different from each other in severity and repair cost.
- 3E1 — the motor cannot reach the commanded speed. Usually caused by an overloaded drum or a failing tachometer that misreads the motor's actual rotation rate. Reduce the load and restart before assuming the motor has failed.
- 3E2 — the motor is drawing too much current. This indicates mechanical obstruction in the drum or a bearing worn to the point of creating significant drag. Turn the drum by hand with the machine unplugged. Resistance or grinding suggests a bearing failure.
- 3E3 — the motor has overheated. Usually follows a long cycle with an overloaded drum. Let the machine cool for 30 minutes before restarting. If it runs clean after cooling, reduce your load size on future cycles.
- 3E4 — inverter control fault on direct-drive models. The inverter board has failed to communicate with the motor correctly. This is a control board issue, not a motor issue, and the two carry very different repair costs. A technician with the Samsung diagnostic software can confirm which component is the fault before a part is ordered.
Lr (Locked Rotor):
The drum cannot rotate at all. The motor receives a start signal and nothing moves. This is one of the less-discussed Samsung codes, and one of the more important ones to handle correctly. With the machine unplugged, turn the drum by hand. If it rotates freely, the motor or its drive circuit has failed. If the drum will not turn by hand, something is physically jamming it, check for a foreign object lodged between the drum and the housing before assuming a motor failure.
What to try for base 3E codes: Reduce the load, let the machine cool if it has been running long cycles, and restart. For 3E4 or Lr with a freely-rotating drum, stop. These require a technician.
9. Communication and Control Board Errors: AE, AE3–AE6, bE
AE codes:
AE indicates a communication failure between the main control board and another component. The sub-code is more important than the base code, and they are not interchangeable faults.
- AE3 — communication fault between the main board and the display panel. The machine may still function but the display is unreliable or frozen.
- AE4 — communication fault between the main board and the motor control module. The machine may refuse to start or stop mid-cycle without completing the fault condition.
- AE5 — Wi-Fi or SmartThings connectivity error on smart models. The appliance continues to function physically; it simply will not talk to the app. Not a repair-urgency issue. Check your router's 2.4 GHz settings before calling anyone.
- AE6 — internal communication fault within the main control board. The most serious AE sub-code. The board itself has a problem. Persistent AE6 after a full power cycle requires a technician and potentially a board replacement.
What to try: Full power cycle for any AE code, unplug from the wall for 5 minutes. Power surges and firmware anomalies occasionally produce AE codes that clear permanently with a full reset. If the code returns on the next cycle, do not keep resetting. Repeated resets on a board fault do not fix the fault.
bE (button error):
One or more buttons on the control panel are registering as stuck or shorted. Inspect the panel for physically stuck buttons, particularly around the cycle selector. Clean around the buttons with a dry cloth. If the touchpad has failed electrically rather than mechanically, the panel assembly needs replacing.
10. Water Level, Overflow, and Leak Errors: 1E, OE, LE
1E (water level sensor fault):
The pressure sensor that measures drum fill level has failed or is reading incorrectly. Symptoms include the machine filling continuously without stopping, or refusing to fill at all because the sensor is reporting the drum as already full. The pressure sensor and its connecting hose are a parts replacement — not a DIY component on most models due to the disassembly required to access them.
OE (overflow):
The drum has filled beyond the safe level. Common causes: a stuck-open inlet valve that will not close when the drum reaches the correct level, or a 1E sensor failure that prevents the fill signal from being received. Do not restart after an OE code without identifying why the overfill occurred. The excess water has to go somewhere, and on a front-loader that somewhere is the motor cavity and control board.
LE (low level / leak detected):
On most Samsung models, LE means water is leaving the drum faster than expected — either through a damaged door seal, a loose hose fitting, or a crack in the drum housing. Check the door gasket for cracks or tears. Check all hose connections at the back of the machine for drips. If the machine is actively leaking onto the floor, do not run another cycle until you have found the source. Water under a washing machine is not a situation that improves with patience.
11. Voltage Error: UC
What it means: The machine has detected that the supply voltage is outside its safe operating range — too high or too low. Canadian standard is 220 to 240V. A UC code typically follows a power outage, a voltage spike, or a circuit under abnormally heavy load.
What to try: Power cycle after waiting a full minute for the supply voltage to stabilise. If you had a recent outage or circuit trip, the voltage transient may have cleared on its own.
What to check if it recurs: Confirm the washing machine is on a dedicated circuit. Samsung front-loaders draw significant current on spin, sharing a circuit with a refrigerator, dishwasher, or electric kettle can create transient low-voltage conditions during the overlap. Most Canadian building codes require a dedicated 15A or 20A circuit for laundry appliances. If yours is shared, that is the root cause.
When to call a technician: Persistent UC codes on a dedicated circuit with stable supply voltage indicate the machine's internal voltage monitoring circuit has failed.
12. Samsung Diagnostic Mode: The Feature Samsung Forgot to Mention in the Brochure
This is the section that competitors consistently skip, and it is the most useful tool most Samsung washer owners have never used.
Samsung front-loaders and most top-loaders manufactured from 2015 onward include a built-in diagnostic mode that runs each component in sequence, water inlet, drum rotation, drain, spin, heating, and reports faults for each one independently. The error code on your display is the symptom. Diagnostic mode identifies the cause.
How to enter it on most Samsung front-loaders:
Press and hold Temp and Delay End simultaneously for 3 seconds. The display will show a diagnostic indicator. Press Start to begin the sequence. The machine runs through each system and shows a code for any component that fails its individual test.
Why this is useful: If your machine is showing a 5E code, the drain pump filter is the most likely cause — but diagnostic mode can confirm whether the pump motor itself has also failed before you spend time on the floor with a towel. It also surfaces secondary faults that the surface-level error code does not show. A machine showing 4E may have a failing inlet valve and a developing tE fault, the panel shows only the code that triggered first.
Important caveat: The button combination to enter diagnostic mode varies by model series. The sequence for a WF45 front-loader differs from a WA-series top-loader. Before attempting, confirm the correct sequence for your specific model number via Samsung's official support documentation. If you cannot find it, this is an excellent question to ask a technician during a diagnostic visit, they can run it, read the full output, and explain what each result means.
13. Repair vs. Replace: The Honest Framework
Samsung washing machines are repairable. Parts for most models manufactured after 2015 are available across Canada, and the repair network for Samsung is significantly better than for some European brands. That is the good news.
The less comfortable truth is this: Samsung's error code system is designed to be read by Samsung's proprietary diagnostic software. The codes on the panel are surface indicators. A general handyman looking up your code online is working from the same information you already have — they are not accessing the sub-code fault data that tells a technician whether the issue is a $90 sensor or a $450 control board. This matters enormously when you are deciding whether a repair is worth authorising.
According to Natural Resources Canada's appliance efficiency guidance, washing machines are designed for a useful life of approximately 10 to 14 years with regular maintenance. Use that alongside the 50% rule:
- Under 5 years old: repair almost any fault. The machine is young, parts are current, and the repair will return years of use.
- 5 to 8 years old: repair non-board faults (drain pump, door latch, suspension rods, door seal). Get a firm written quote before authorising control board or motor replacements, the numbers need to make sense against the machine's remaining lifespan.
- Over 9 years with a board or motor failure: apply the 50% rule directly. If the repair exceeds half of what a comparable new Samsung costs, lean toward replacing. A drum bearing failure on a 10-year-old front-loader is a different conversation than the same repair on a 4-year-old one.
- Any age with a SUd, UE, or basic door code: almost never a reason to replace. These are maintenance and operation issues, not component failures.
We run this assessment on every Samsung washer diagnostic call. If the repair does not make financial sense for the age and condition of the machine, we say so before starting work. That is the whole point of a diagnostic visit, to know what you are dealing with before committing to a repair.
And if the laundry pile has been growing since the error code first appeared three weeks ago and has now reached a height that requires its own postcode, that is nature's way of accelerating your decision-making process.
About the author
Max is a certified appliance repair technician with 19 years of experience serving Port Coquitlam and the Lower Mainland. He is the lead technician at ElectraFix Appliance Repair Ltd. and has diagnosed and repaired Samsung washing machines across Greater Vancouver since 2007. He holds the Technical Safety BC gas certification and has seen every code on this list, several of them within the same week.
ElectraFix Appliance Repair Ltd. — 950 Seaborne Ave #2120, Port Coquitlam, BC | (778) 941-7758
Frequently Asked Questions
How do I reset my Samsung washing machine after an error code?
Press Power to turn the machine fully off. Wait 30 seconds. Press Power to restart. This clears transient faults caused by power fluctuations, momentary sensor readings, or software hangs. If the code returns within two cycles, the underlying component has failed and a reset will not resolve it — stop clearing the code and address the cause.
What is the most common Samsung washing machine error code?
The 5E (drain error) and 4E (water supply error) codes account for the large majority of Samsung washer service calls. Most 5E codes resolve by cleaning the drain pump filter behind the bottom front access panel. Most 4E codes resolve by confirming the supply tap is fully open and cleaning the inlet mesh filter at the back of the machine. Both are straightforward checks before calling anyone.
Can I fix Samsung washer error codes myself?
Some, yes. The 5E (clean the drain filter), 4E (check the water tap and inlet filter), UE (redistribute the load), SUd (switch to HE detergent and use less of it), and basic door errors (remove caught laundry) are all reasonable DIY steps. Codes pointing to the control board, motor, or heating element require a technician. Always unplug the machine and wait five minutes before opening any access panel — the capacitors hold a charge after the power is cut.
Does DIY troubleshooting void my Samsung washing machine warranty?
Cleaning the drain filter, checking hose connections, redistributing laundry, and running a reset do not affect warranty coverage — these are maintenance tasks described in Samsung's own documentation. Opening the machine's casing, replacing internal components yourself, or causing secondary damage during a DIY repair attempt can void the warranty on the components involved. If the machine is within its warranty period, contact Samsung support before doing anything beyond basic filter and hose checks.
How do I enter Samsung washing machine diagnostic mode?
On most Samsung front-loaders from 2015 onward, press and hold Temp and Delay End simultaneously for 3 seconds. The machine runs each component in sequence and reports faults independently. The button combination varies by model series — confirm the correct sequence for your specific model number before attempting. If you cannot find it, ask a technician to run it during a service visit and explain the results.
When should I stop troubleshooting and call a technician?
Stop and call when: the same code returns after two resets; the code involves the motor (3E4, Lr), control board (AE6, persistent AE4), or heating element (HE, recurring tE); the machine is actively leaking onto the floor; or the drum will not rotate by hand with the machine unplugged. Samsung's sub-codes look identical on the display but indicate faults with very different repair costs — a technician with service software reads the full fault data, not just the surface code you can see.
The code cleared. It came back. Now it is personal.
We diagnose Samsung washing machines across the Lower Mainland with the service software that reads what the panel does not show you. If you know what the code is but not what is causing it, that is exactly what a diagnostic visit is for. We confirm the fault, quote the repair, and wait for your answer before touching anything.
ElectraFix Appliance Repair Ltd. — Port Coquitlam and the Lower Mainland